Can I Set Up a Tub Myself? Considerations As Well As Steps
Can I Set Up a Tub Myself? Considerations As Well As Steps
Blog Article
Presented here below you will discover lots of high-quality details on the subject of How to Install a Bathtub Yourself.
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably challenging job. If the old tub is readily obtainable, the task can relocate immediately; if you have to open a wall to get rid of the old bathtub as well as position the new bathtub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. Ensure you have certified on your own for the task and fit trying it. Instead of hiring a service provider to take over a halfway-completed task, it is much better to think about employing one before you start. Opportunities are you might need an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually currently gotten a new tub and also do not need to change the setup of your previous water supply pipes.
Your devices as well as product list should consist of the following:
Planning for the Setup
To start with, the sustaining frame provided with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to prevent stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, then the first thing you need to do is detach the water supply. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for position. The wooden boards are useful in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water and also inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub and additionally inspect the overflow outlet as well as the normal outlet for leakages.
Ultimately, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bathtub must wait up until the bathtub has actually been utilized at least when as this will certainly resolve it right into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Protect the faucet in place with the supplier supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture a rigid seal, creating the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to permit the activity experienced when the tub is in use. The sealant can fracture rather early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very drawn to How to Install a Bathtub Yourself and I really hope you liked my article. Sharing is nice. Helping others is fun. We value reading our article about Tools You Need to Install a New Bathtub .
Click Here To Find Out More
Report this page